SPI LED Controller Mi-Light SPIR3 3 in 1 – WS2811 / WS2812 digital strips, 2.4G remote, 10 A
SPI LED controller 3 in 1 for digital (addressable) single-colour, RGB and RGBW strips – 5–24 V DC, 10 A, up to 2048 pixels, 20 dynamic modes. Controlled by the C6 remote or B6 wall panel (2.4G RF, 30 m) and a PUSH switch. No chip-type setup needed.
10,00 €/ pcnet
The message will already contain this product's name and code.
*The prices shown are for information purposes only and do not constitute a commercial offer within the meaning of Art. 66 §1 of the Civil Code of the Republic of Poland. The exact quotation is always determined individually after a request for quotation has been submitted and reviewed, or after an inquiry sent directly by email.
The Mi-Light (MiBoxer) SPIR3 is a 3-in-1 SPI LED controller for digital (addressable) strips – single-colour, RGB and RGBW – with a 2.4G RF receiver. The output mode is switched with the SET button on the housing and the strip’s driver chip needs no configuration: the controller supports WS2811, WS2812, WS2813, WS2815, SK6812 (RGBW), WS2814 (RGBW), UCS1903, TM1812 and more. 5–24 V DC input, up to 10 A output (50–240 W), SPI (TTL) 800 Kbps signal, up to 2048 pixels in mono, 1536 in RGB and 1024 in RGBW. 20 dynamic modes with editable colours, length and colour setting, on/off timer and a DND function (power saving after a mains failure). WiFi (Tuya) + DMX version: SPIW5 WiFi SPI controller.
Ways to control it
- 2.4G RF remote or wall panel – the Mi-Light C6 remote for SPI strips (modes, colour, brightness, timer, effect editing) or the Mi-Light B6 wall panel; range up to 30 m.
- PUSH switch – GND/PUSH terminals: on/off and dynamic-mode change from an ordinary momentary switch.
- Pairing: power on and press SET once (linking mode); details in the PDF manual.
Compatible remotes and panels (2.4G RF, purchased separately)
C6 (SPI RGB remote) and B6 (SPI touch panel). For analogue (non-SPI) strips use the Mi-Light E3-RF 3 in 1 controller instead. A matching digital strip from our range: WS2811 COB strip.
Technical data
- Model: Mi-Light / MiBoxer SPIR3 (3 in 1 SPI LED Controller, 2.4GHz)
- Input voltage: 5–24 V DC
- Output current: max 10 A; power 50–240 W (constant voltage)
- Output signal: SPI (TTL) 800 Kbps; pixels: mono 2048 / RGB 1536 / RGBW 1024
- Supported chips: TM1809, TM1804, TM1812, SK6813, UCS1903, UCS1909, UCS1912, UCS2903, UCS2909, UCS2912, WS2811, WS2812, WS2813, WS2815, SK6812 (RGBW), WS2813 (RGBW), WS2814 (RGBW)
- Control: 2.4G RF (30 m range), PUSH switch; 20 dynamic modes, colour editing, ON/OFF timer, DND function
- Dimming: 4096 levels, 0.1–100 %, logarithmic curve
- Size: 74.5 × 36 × 17 mm; IP20; operating temperature −10…+40 °C
- Certification: CE (EMC, LVD, RED); 5-year manufacturer warranty
Remote, panel and power supply are not included. Match the power supply to the strip voltage and total load – see the PDF manual below.
